DIY Tub Installation.
DIY Tub Installation.
Blog Article
Just about every person has got their own individual opinion with regards to Installing A Bathtub.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is readily available, the job can move rapidly; if you need to open a wall to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need a helper to leave the old tub and also embeded in the new one. Make sure you have qualified on your own for the work and are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed task, it is better to think about employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube links.
This write-up will help you set up a brand-new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not require to transform the plan of your previous water system pipes.
Your tools and also product list need to consist of the following:
Getting ready for the Setup
First of all, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps system to prevent pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, position the tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The following goal is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the tub up until the spirit level reviews level.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the water system as well as examine all joints as well as new pipework for leakages as well as tighten them if required. Load the bathtub as well as likewise examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub needs to wait until the tub has been utilized at least once as this will certainly resolve it right into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former kind must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, resulting in complications with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can crack rather early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is advisable to fit the tiles making use of waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about Installing A Bathtub? Put feedback further down. We'd be delighted to hear your responses about this blog entry. In hopes to see you back again later on. Liked our blog? Please share it. Help somebody else check it out. Thank you so much for your time invested reading it.
Check This Out Report this page